Journeys Month 5 – Homeward Bound

Welcome to Stitchin Heaven’s Journeys Month 5. My helper for Month 5 is Deb Tucker, of Studio 180 Design. This month you are going to learn to make Lemoyne Star Quarters using the Rapid Fire Lemoyne Star and Tucker Trimmer I tools. You will be using Prints 7, 9 & 11. Label your fabrics and use your best cutting skills when cutting your starter squares.

Piecing Instructions

Step 1 – Organize Strips. Place Print 9 and Print 7 into two separate piles. Use Print 7 to make the A Strip Set and Print 9 to make the B Strip Set.

Step 2 – Make Strip Sets A and Strip Sets B in the same manner as described in the Rapid Fire® Lemoyne Star basic instructions. Position each diamond strip 4¾” down from the top of the background strip. Sew the strips lengthwise and press as indicated in the diagram below. Pay close attention to proper strip alignment and pressing to ensure success.

Step 3 – First Cuts. Layer Strip Set A and Strip Set B right sides together as illustrated. Trim the ends of the strips at a 45° angle, then continue making 45° angle cuts every 3¼” across the length of the strips. You will get 8 cuts from a paired strip set. Cut the remaining strip sets in this manner until you have 20 pairs.

Step 4 – Make Second Cuts going vertically south to north, as shown. Position the ruler edge at the tip of the star strip and trim straight up. These triangles will be added to the pieced unit.

Jackie’s Tip for staying organized is to label two paper plates A & B. For Right handers, Strip “A” is on top & Strip “B” is on the bottom. Cut one unit at a time, place the “A” unit on plate marked “A” & the “B” unit on plate marked “B”. You will always know which units are A & B for pressing.

Step 5 – Arrange, position and stitch the cut pieces together into pieced triangle units. Press as shown in the diagram to yield future nesting seams.

You can chain stitch your “A” and “B” units for easier pressing
Press “A” units toward the Star Point
Press “B” units toward the side triangle

Tip: Remember “whatever you are pressing toward – goes on top”!

Step 6 – Trim down all pieced triangle units using the 12” line on the Rapid Fire® Lemoyne Star tool as shown in the diagram.

Step 7 – Assemble quarters. Arrange the sewn and trimmed A and B sections into quarter blocks. Stitch the sections together and press the seams open to best distribute bulk. You should have 20 quarter blocks total.

You can choose to press your seams open or…
You can choose to press the seams so they are all going in the same direction.

Step 8 – Trim the quarters to 6½” x 6½” with your Tucker Trimmer® I tool. Clean up the dog ears and true up the first corner as shown (this should just be a few threads at most), then rotate the unit 180o to trim the opposite corner. Align the Common Diagonal with the seam and the 6½” clean up lines with the trimmed edges to trim the remaining two sides. Repeat for all 20 quarters. Label the finished quarters Unit H.

First Trim
Second Trim

Recap: Make 20 Unit H – Homeward Bound Units.

Homeward Bound, Unit H

Congratulations, you have learned to use your Rapid Fire Lemoyne Star tool!

8 thoughts on “Journeys Month 5 – Homeward Bound

  1. Robert Hooper

    In Steps 3/4 do you have any advice or trick for keeping Strips A and B nested together so that all cuts are accurate–glue, pins, etc.?? Thank you. Terri H.

    Like

    Reply
    1. ifthesethreadscouldtalk Post author

      I start out by making sure “A” & “B” are pressed well . I check after each cut to be sure they are still nested. If they separate a little , re-align the nesting seams. If after re-aligning the nesting seams, if it cause the edges to NOT align, just place the 45 degree line on the bottom of the set and slide over to trim what should be very little. Sometimes Deb Tucker will press unit with the iron to keep them together, but you would them have to move “A” & “B” to the cutting mat and check again the seams are nested.

      Like

      Reply
  2. judyschulz

    I enjoy your instructions. I’m a visual person so it’s really a help to me to see how these rulers are set before cutting. I do have two questions. First in step 4: It appears by the pictures that you have set a point at 1/4 above the seam line to make the 45 degree cut straight up. Is that correct? Question 2: in step 5, do I center the triangle to the cut edge before sewing? Any advice will be greatly appreciated.

    Like

    Reply
    1. ifthesethreadscouldtalk Post author

      Judy, If you are right handed and cut your units from left to to right, there would be a a star strip point that you would use as a guide to place your ruler. II did not take these photo’s. I think these were cut by a left handed person. Deb Tucker refers to this on page 3 of the instructions in a Note paragraph. I hope this clears this up. Let me know.

      Like

      Reply

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s